Floors That Stop Absorbing Spills
Basement Sealing in Saint George and Provo, UT, for Concrete Stained by Oil, Grease, and Years of Wear
Older basement slabs in Saint George and Washington were poured directly on grade during the 1970s and 1980s, when builders used concrete as a structural base rather than a finished floor, and those slabs have spent decades absorbing oil from stored equipment, grease from workbenches, and solvents from decades of home maintenance projects. The contamination soaks into the pores and will bleed through a coating unless the slab is ground first. Rhino Concrete Coatings diamond grinds the concrete to remove the stain layer and open the pores, then applies a sealing system that bonds directly to the cleaned substrate, so you end up with a floor that sheds spills instead of absorbing them.
The grinding step strips contamination that has penetrated the concrete and creates the surface profile the coating needs to bond, which replaces the separate degreasing step that leaves chemical residue on the slab. Once the slab is clean, an epoxy base coat is applied, and a polyaspartic topcoat is added when the floor will see continued chemical exposure from workshop use or storage. The depth of grinding depends on how far the stain has penetrated, and the crew evaluates that at the estimate by looking at how the concrete reacts to water and whether the discoloration is surface-level or has soaked several millimeters deep.
Request a detailed estimate to determine how much grinding your slab requires and which coating system matches your intended use.
Diamond grinding removes the contaminated concrete mechanically, which is more effective than trying to dissolve years of oil and grease with solvents that leave their own residue. The grinder exposes fresh aggregate across the entire slab and opens the pores so the base coat can penetrate and bond, rather than sitting on top of a contaminated layer that will eventually delaminate. Epoxy is used as the base coat on every job because it bonds well to concrete and acts as its own moisture vapor barrier, which matters in basements where some vapor transmission is normal.
Once the coating cures, you will notice that spills sit on the surface long enough to be wiped up, dust no longer works its way into the pores, and the floor can be mopped without water soaking into the concrete and leaving streaks. The coating does not change the structural integrity of the slab, but it does stop contamination from soaking in and makes the surface easier to maintain over the decades the floor will remain in service.
The sealing process includes grinding, crack repair, base coat, topcoat and cleanup, but it does not include removal of heavy coatings applied by previous contractors or structural repairs to slabs that have cracked deeply or shifted due to foundation movement. If the slab has large cracks that move when walked on, or if there are hollow-sounding sections, those need to be addressed before coating begins.
Answers About How the Work Is Done
Homeowners in Saint George often ask whether an old basement floor can be sealed effectively or if the contamination has penetrated too deeply to be addressed without replacing the slab.
How does the crew determine how much grinding the slab needs?
The crew looks at how water beads or soaks into the concrete, checks whether the staining is uniform or concentrated in specific areas, and tests a small section to see how deep the discoloration extends, which determines how many passes the grinder will make before the concrete is clean enough to coat.
What happens if the stain has soaked deeper than the grinder can reach?
If the contamination has penetrated several millimeters deep, the grinder is adjusted to remove more material, though there is a practical limit to how much concrete can be ground away before the aggregate is exposed unevenly, at which point a thicker base coat is used to fill the profile.
Why is epoxy used as the base coat instead of applying polyaspartic directly to the slab?
Epoxy bonds to concrete more effectively than polyaspartic and acts as a moisture vapor barrier, which is important in basements where some vapor transmission through the slab is normal, while polyaspartic is added as a topcoat when chemical resistance and fast curing are needed.
What should you do to prepare the basement before the crew arrives?
Clear the floor of stored items, move furniture and equipment away from the walls, and make sure the crew has access to an exterior door or large window for ventilation, since the grinder produces dust even with vacuum attachment.
How long does the sealed floor take to cure before you can move equipment back into the basement?
Foot traffic is usually safe within 24 hours, and light equipment can be moved back after 48 hours, though full cure takes several days and heavy loads should wait until the coating has hardened completely.
Rhino Concrete Coatings also
seals basement floors in Cedar City, Hurricane, Washington, Ivins, Santa Clara and Mesquite. Free estimates are provided on every project, and the crew will evaluate stain depth and explain which coating system matches how you use the space.
