Floors Designed as Features, Not Utilities

Metallic Epoxy Floor Coatings in Saint George and Provo, UT, for Garages, Showrooms, and Commercial Spaces Where Style Meets Durability

Newer homes with finished garages and showrooms across Saint George and Ivins increasingly treat the floor as a visual feature rather than a background surface. Metallic epoxy floor coatings produce a swirled, reflective finish that reads as intentional design, and each floor is built on the same bonded substrate used in commercial work. Rhino Concrete Coatings applies metallic coatings in Saint George, Utah and across southern and northern Utah, diamond grinding every slab to bare concrete so the pigment layer sits on open pores with a moisture vapor barrier underneath.


Diamond grinding removes the existing surface entirely and exposes the slab's pore structure so contamination, old sealers and carbonation are gone before the new system starts. A moisture vapor barrier is applied first to prevent the thick pigment layer from trapping moisture that would otherwise blister or delaminate the coating. One flood coat of metallic pigment is then spread at roughly 50 to 80 square feet per gallon, which allows the material to pool, shift and cure into the characteristic swirled pattern, and a topcoat at about 200 square feet per gallon seals the design and provides abrasion resistance.


Arrange an on-site consultation to review pigment options and slab conditions before the coating schedule is set.

What Separates a Metallic Floor from Standard Coatings

Metallic coatings use a single heavy application of pigmented epoxy rather than a thin base coat, so the material has enough body to move and form patterns as it cures instead of laying flat. The pigment contains metallic powder that reflects light at different angles depending on how the coating settled, which is why the floor appears to shift in color or depth as you move across it.


After the topcoat cures, you'll notice the floor is smooth, glossy and visually complex without requiring multiple colors or decorative inlays. The swirled effect is permanent and won't fade under UV exposure because the pigment is locked beneath a clear polyaspartic topcoat that resists yellowing and chemical staining. The surface handles the same traffic and impact loads as a standard epoxy floor, so durability isn't traded for appearance.


The vapor barrier step adds time to the installation but prevents the most common failure mode in thick-coat systems—moisture pressure from below that lifts the coating in sheets or forms bubbles along the bond line. Each layer is allowed to cure fully before the next is applied, so the finished floor is stable under both mechanical load and environmental exposure.

Common Questions Before Installing Metallic Floors

Showrooms, finished garages and commercial spaces in Saint George and Washington County want floors that function as design elements without introducing maintenance problems or early failures.

  • How is the metallic pattern controlled during application?

    The pigment is spread at a specific thickness and allowed to self-level and cure naturally, so the pattern forms based on how the material flows rather than being manipulated with tools, which means each floor is unique but the general style remains consistent.

  • Why is the slab ground back to bare concrete before a metallic coating?

    Any sealer, curing compound or contamination left on the surface will prevent the epoxy from bonding, and because the pigment layer is thick and heavy, weak adhesion leads to wholesale delamination rather than small isolated failures.

  • What does the moisture vapor barrier prevent?

    It stops water vapor migrating up through the slab from reaching the thick epoxy layer, which would otherwise cause blistering, bubbling or edge lifting as pressure builds beneath the coating.

  • What changes once the topcoat is applied?

    The floor becomes abrasion resistant, chemical resistant and easier to clean, and the metallic pattern is locked in place so it won't scuff, fade or wear unevenly under traffic.

  • How does a metallic floor hold up in a high-traffic garage or showroom?

    The topcoat is the same polyaspartic system used on commercial floors, so it resists tire marks, impacts, spills and scuffing at the same level as a standard coating, with the metallic layer protected underneath.

Rhino Concrete Coatings also applies metallic epoxy floor coatings in Hurricane, Washington, Ivins, Santa Clara and Mesquite. Free estimates are provided on every project, and the standard pricing system holds quality constant while keeping costs competitive.